TopTro TR25 Main Board Replacement

Written By: Keion.M.Shelton
  • Comments: 0
TopTro TR25 Main Board Replacement

Difficulty

Moderate

Steps

8

Time Required

10 - 20 minutes

Introduction

If you want to replace the circuit board, use this guide. For this guide you will need an opening tool and a screwdriver. The steps aren't difficult but require you to be careful as the cords are weak.

  1. cRAu6SWkPTfWHmmc
    cRAu6SWkPTfWHmmc
    3kqOATvTYfJOXKyM
    N1lDtVJ5CGOC2IEm

    • Insert an opening pick in the seam between the top panel and chassis.

    • Pry around the entire perimeter of the top panel until it fully releases.

    • Remove the top panel.

  2. ro4ZejOPSHrbvYDV
    ro4ZejOPSHrbvYDV
    bViKALhP5syKt4UR
    HRrrGKJFKyrThcCG

    • Unplug the cord connecting the top button panel to the projector,

    • Make sure to disconnect the end connected to the panel and not the chassis.

    • The cord is small and sensitive and could sustain damage if pulled out aggressively.

  3. gMTECrJElSX1hbti
    gMTECrJElSX1hbti
    uFYHPxvsy4hTINdc

    • Insert a spudger into the semi-circle panel indent and pry up to remove it.

  4. FJ644EVYu2XmPXIM
    FJ644EVYu2XmPXIM
    bZGHQhGkXcRT3uCe
    DnFJ5aclNompHRAD

    • There are three Phillips screws securing the case on. Two are inside the opening left by the previous step, and the third is located on the underside of the projector. Remove all three.

    • The third sticker may be located underneath a QA (quality assurance) sticker. If you are having trouble finding it, look for that sticker.

  5. tkLCD1A6QeKUKiin
    tkLCD1A6QeKUKiin
    ahUEOqkoXY5EkX2I
    tfQ6sXI525RKfBNM

    • Insert a spudger into the seam between the lower panel and chassis.

    • Pry around the perimeter until the lower panel fully releases.

    • We suggest starting at the front, but starting from any side will work.

  6. 2BHWGTgUDtunKkNE
    2BHWGTgUDtunKkNE
    juv1Y2KCnNCqva6M

    • Remove the case from the projector and set it aside.

  7. SIxsTXbdNjSxKDAu
    SIxsTXbdNjSxKDAu
    aoEkA62ijOcgE4KJ

    • Disconnect all of the motherboard connectors.

    • The cables are small and thus subject to damage if removed improperly or aggressively.

  8. bTfNb1Iwg1YMtXDW
    bTfNb1Iwg1YMtXDW
    GZINB6bdC56PsrB4
    YOCxV6WPgqW1ekPY

    • Flip the board over with care not to damage the attached ribbon cable.

    • Flip up the black locking ZIF flap that secures the ribbon cable.

    • Disconnect the ribbon cable.

    • Remove the main board.

Conclusion

To reassemble your device, follow the above steps in reverse order.
Take your e-waste to an R2 or e-Stewards certified recycler.
Repair didn’t go as planned? Try some basic troubleshooting or ask our Answers community for help.

Author

Keion.M.Shelton

Member since: 28/08/24

497 Reputation

0 comments